Rubi DT250EVO Betreibershandbuch

OPERATOR’S MANUAL10 in. TILE SAWMANUEL D’UTILISATIONSCIE À CARREAUX DE 254 mm (10 po)MANUAL DEL OPERADORSIERRA DE LOSAS DE 254 mm (10 pulg.)DT250EVOCO

10 — EnglishFEATURESKNOW YOUR TILE SAWSee Figure 3.The safe use of this product requires an understanding of the information on the tool and in this o

11 — EnglishLOOSE PARTSThe following items are included with your tile saw:Fig. 5A - Water tray frame assembly ...1B

12 — EnglishUNPACKINGSee Figure 5.This product requires assembly. Carefully lift the saw from the carton and place on a level work surface. WARNING

13 — EnglishFig. 6ASSEMBLYRIGHT OUTER TUBELEFT UPPER TUBESPACERLOCK NUTRIGHT UPPER TUBEINNER LEG ASSEMBLYCENTER BRACEAXLELOCK NUTFLAT WASHER, SM

14 — EnglishINSTALLING THE WATER TRAY FRAME ASSEMBLY TO THE LEG STANDSee Figure 7.Lock the table stop by-pass by pulling up on the stop and turning

15 — EnglishFig. 9CONNECTORCLEAR TUBEWATER FILL LINEINNER LEG ASSEMBLYASSEMBLYINSTALLING THE WATER TRAY AND TRAY EXTENSIONSSee Figures 10 - 12.Fr

16 — EnglishASSEMBLYINSTALLING THE MITER GUIDESee Figure 13.The miter guide can be used from both the left and right side of the cutting wheel.Place

17 — EnglishTO CLOSE / OPEN THE LEG STANDSee Figures 15 - 17.Remove water tray, water tray extensions and the water tank, and any workpieces from th

18 — EnglishASSEMBLYTILE CUTTING WHEELFor maximum performance and safety, it is recommended that you use the 10 in. cutting wheel provided with your s

19 — EnglishASSEMBLY Place an outer washer onto the spindle. The double “D” flats on the washer align with the flats on the spindle. Be sure the hol

2 — English Introduction ...

20 — English WARNING:Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict

21 — English891011121314ON/OFF SWITCHSee Figure 23.This saw is equipped with an on/off switch that has a built-in locking feature. This feature is int

22 — EnglishOPERATIONMAKING CUTSAlways draw the line to be cut on the tile using a marker or grease pencil. If the tile is shiny and hard-to-mark, pla

23 — EnglishTO MAKE A MITER CUTSee Figure 28.Miter cuts are used for cutting outside and inside corners on material, decorative chair rail, and base m

24 — EnglishOPERATION Turn the material over and make the cut along one of the marks. This time overcut the other line and the cut piece should sepa

25 — English WARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is in the OFF position. Fa

26 — English WARNING:When servicing, use only identical replacement parts. Use of any other parts could create a hazard or cause product damage. WARNI

27 — EnglishMAINTENANCELUBRICATIONAll of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the

3 — EnglishGENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric

4 — EnglishGENERAL SAFETY RULES KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from wheels. Do not reach underneathwork or around or over the w

5 — English SECURE WORK firmly against the miter guide or fence.  NEVER stand or have any part of your body in line with the path of the wheel.

6 — EnglishSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbols

7 — EnglishELECTRICALELECTRICAL CONNECTIONThis tool is powered by a precision built electric motor. It should be connected to a power supply that is 1

8 — EnglishELECTRICALGround Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for the tile saw.

9 — EnglishPRODUCT SPECIFICATIONSWheel Diameter ...............10 in.Wheel Arbor .......